Jump to content

Layer 2 NOT Activated και Point-to-Multipoint / Point-to-point.


heavyaris
 Share

Recommended Posts

Καλησπέρα, θα ήθελα να περιγράψω ένα πρόβλημα που αντιμετωπίζω στη προσπάθεια να περάσω voice σε εναν cisco 2911 με 2 τηλεφωνικές γραμμές - Wind + οτε

 

Δεν μπορούμε να λάβουμε κλήσεις στο interface του οτε: BRI0/2/0

 

Παραθέτω το debug:

 

 

ISDN BRI0/2/0 interface ----> εδώ είναι το πρόβλημα

        dsl 8, interface ISDN Switchtype = basic-net3

        Layer 1 Status:

        DEACTIVATED      Όταν γίνεται μια εισερχόμενη γίνεται ACTIVE

        Layer 2 Status:

        Layer 2 NOT Activated     Όταν γίνεται μια εισερχόμενη παραμένει NOT Activated (κανονικά πρέπει να εμφανίζει ότι και στην κάτω isdn)

        Layer 3 Status:

        0 Active Layer 3 Call(s)

        Active dsl 8 CCBs = 0

        The Free Channel Mask:  0x80000003

 

Ενώ στην wind όλα πάνε μια χαρά

 

ISDN BRI0/2/1 interface       

        dsl 9, interface ISDN Switchtype = basic-net3

        Layer 1 Status:

        ACTIVE

        Layer 2 Status:

        TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED  

        Layer 3 Status:

        0 Active Layer 3 Call(s)

        Active dsl 9 CCBs = 0

        The Free Channel Mask:  0x80000003

        Total Allocated ISDN CCBs = 0

[/code]

 

Μόλις βγάζουμε το rj45 από το netmod της wind (που δουλεύει έτσι και αλλιώς) δεχόμαστε κλήσεις αλλά μετά από 2 ώρες, σταματάει να δέχεται…!

 

Βρήκα σε διάφορα ξένα forums τα εξής:

 

-I've had the same problem a couple of times before.

 

-Check that Telstra have set the line up as Point-to-Multipoint and not Point-to-point.

 

-If they have set the line up as Point-to-point you will never get layer 2 up.

 

Checked with Telstra, the line was configured as point-to-point, had them

change it to point-to-multipoint and all is now working fine.

 

----------------------------------------------------------------------------------------------------------

 

ISDN telephone works on the line - the problem was that the telco had

set the line to point-to-point rather than point-to-multipoint.

Router can connect now, just sorting out some routing issues now.

 

Πληροφορίες για το τι είναι το καθένα:

 

Point-to-multi-point (also known as Standard Access or S/T reference point)

This is the normal configuration for ISDN2e circuits. It allows up to eight separate devices to connect to the circuit. These may be Terminal Adapters, PC cards, ISDN telephones etc. In this configuration, MSN telephone numbers route calls to the individual devices/ports/applications.

 

Point-to-point (also known as System Access or T reference point)

In this configuration only one device is connected to the ISDN2e circuit. This is normally a PBX, which routes calls to extensions using DDIs.

 

Λοιπά ενδιαφέροντα λίνκ:

 

http://www.hwkb.com/Uwe/Forum.aspx/network-cisco/7189/Cisco-801-BRI-layer-2-status-inactive

 

Εδώ λέει να γίνει point-to-point από τον πάροχο.

 

Layer 1

 

http://www.cisco.com/en/US/tech/tk801/tk379/technologies_tech_note09186a0080094b76.shtml

 

Layer 2

 

http://www.cisco.com/en/US/tech/tk801/tk379/technologies_tech_note09186a0080094b77.shtml#identifyingthesourceoflayer2

Link to comment
Share on other sites

  • 1 month later...

Δεν το έχω το προιόν που αναφέρεις.

Αλλά θα σου πω παρόμοιο σύμπτωμα που μπορεί να είναι το ίδιο και σε σένα.

Το link του isnd στον οτε δεν είναι ενεργό από default οπότε δεν ξυπνάει το gateway για να δεχθεί κλήση.

Παίρνεις στο help desk την isdn και ζητάς ενεργοποίηση.

Εαν ισχύει αυτό που σου λέω τότε θα κάνεις το εξής:

Καλέις από οτε και αυτόματα σηκώνετε το link.Θα παραμείνει ενεργό για κάποια ώρα.Κάνεις κλήση στην γραμμή και βλάπεις αν έρχετε η κλήση.

 

 

Link to comment
Share on other sites

 Share

×
×
  • Create New...