heavyaris Posted October 11, 2011 Report Share Posted October 11, 2011 Καλησπέρα, θα ήθελα να περιγράψω ένα πρόβλημα που αντιμετωπίζω στη προσπάθεια να περάσω voice σε εναν cisco 2911 με 2 τηλεφωνικές γραμμές - Wind + οτε Δεν μπορούμε να λάβουμε κλήσεις στο interface του οτε: BRI0/2/0 Παραθέτω το debug: ISDN BRI0/2/0 interface ----> εδώ είναι το πρόβλημα dsl 8, interface ISDN Switchtype = basic-net3 Layer 1 Status: DEACTIVATED Όταν γίνεται μια εισερχόμενη γίνεται ACTIVE Layer 2 Status: Layer 2 NOT Activated Όταν γίνεται μια εισερχόμενη παραμένει NOT Activated (κανονικά πρέπει να εμφανίζει ότι και στην κάτω isdn) Layer 3 Status: 0 Active Layer 3 Call(s) Active dsl 8 CCBs = 0 The Free Channel Mask: 0x80000003 Ενώ στην wind όλα πάνε μια χαρά ISDN BRI0/2/1 interface dsl 9, interface ISDN Switchtype = basic-net3 Layer 1 Status: ACTIVE Layer 2 Status: TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED Layer 3 Status: 0 Active Layer 3 Call(s) Active dsl 9 CCBs = 0 The Free Channel Mask: 0x80000003 Total Allocated ISDN CCBs = 0 [/code] Μόλις βγάζουμε το rj45 από το netmod της wind (που δουλεύει έτσι και αλλιώς) δεχόμαστε κλήσεις αλλά μετά από 2 ώρες, σταματάει να δέχεται…! Βρήκα σε διάφορα ξένα forums τα εξής: -I've had the same problem a couple of times before. -Check that Telstra have set the line up as Point-to-Multipoint and not Point-to-point. -If they have set the line up as Point-to-point you will never get layer 2 up. Checked with Telstra, the line was configured as point-to-point, had them change it to point-to-multipoint and all is now working fine. ---------------------------------------------------------------------------------------------------------- ISDN telephone works on the line - the problem was that the telco had set the line to point-to-point rather than point-to-multipoint. Router can connect now, just sorting out some routing issues now. Πληροφορίες για το τι είναι το καθένα: Point-to-multi-point (also known as Standard Access or S/T reference point) This is the normal configuration for ISDN2e circuits. It allows up to eight separate devices to connect to the circuit. These may be Terminal Adapters, PC cards, ISDN telephones etc. In this configuration, MSN telephone numbers route calls to the individual devices/ports/applications. Point-to-point (also known as System Access or T reference point) In this configuration only one device is connected to the ISDN2e circuit. This is normally a PBX, which routes calls to extensions using DDIs. Λοιπά ενδιαφέροντα λίνκ: http://www.hwkb.com/Uwe/Forum.aspx/network-cisco/7189/Cisco-801-BRI-layer-2-status-inactive Εδώ λέει να γίνει point-to-point από τον πάροχο. Layer 1 http://www.cisco.com/en/US/tech/tk801/tk379/technologies_tech_note09186a0080094b76.shtml Layer 2 http://www.cisco.com/en/US/tech/tk801/tk379/technologies_tech_note09186a0080094b77.shtml#identifyingthesourceoflayer2 Link to comment Share on other sites More sharing options...
filathlos Posted November 30, 2011 Report Share Posted November 30, 2011 Δεν το έχω το προιόν που αναφέρεις. Αλλά θα σου πω παρόμοιο σύμπτωμα που μπορεί να είναι το ίδιο και σε σένα. Το link του isnd στον οτε δεν είναι ενεργό από default οπότε δεν ξυπνάει το gateway για να δεχθεί κλήση. Παίρνεις στο help desk την isdn και ζητάς ενεργοποίηση. Εαν ισχύει αυτό που σου λέω τότε θα κάνεις το εξής: Καλέις από οτε και αυτόματα σηκώνετε το link.Θα παραμείνει ενεργό για κάποια ώρα.Κάνεις κλήση στην γραμμή και βλάπεις αν έρχετε η κλήση. Link to comment Share on other sites More sharing options...
Recommended Posts